RZR 900 Trail Sport 50 INCH

These are the strongest rollers available for the Boss Square puck type secondary clutch.  Replace your square pucks with these rollers before your stock rollers ruin your clutch. Built to withstand the harshest environments and extreme shock-load...

A MUST have for 2016-up Polaris RZR 900/1000 /S/General/XP Owners, upgrading the stock Secondary Boss clutch to the incredible Team Tied Clutch! Kit Includes: Team Tied Secondary Clutch, Gilomen Custom Secondary Spring, Custom Angle Helix...

GILOMEN RX PRIMARY CLUTCH MOVABLE SHEAVE   3068-MOVABLE New replacement movable sheave for the P90 primary clutch If you have a cracked or damaged sheave then this is what you need! Direct fit on the OEM stock polaris 900 and 1000 P90 clutch as...

GILOMEN RX PRIMARY CLUTCH INNER / FIXED SHEAVE   3130-INNER New replacement fixed sheave for the primary clutch on 900cc models.   30mm taper (900cc models have 30mm taper) If you have a cracked or damaged inner sheave then this is...

This is a replacement spider assembly.  It includes rollers, pins, washers, and buttons.  The buttons are the large diameter type which allows them to ride on fresh surface area to tighten up slop from wear.  The buttons are made out of...

This spring is designed specifically for some of our advanced clutch kits and is not designed to be used by itself or with improper components.  

Polaris part # 1521172   This genuine Polaris part fits many Ranger, General, models with EBS (Engine Braking System). Over time, dirt and debris can get in this bearing causing it to drag and eventually seize up. The symptoms of a dragging clutch...

Polaris part # 3514609   This genuine Polaris part fits many Ranger, General, ACE and RZR models without EBS (Engine Braking System). Over time, dirt and debris can get in this bearing causing it to drag and eventually seize up. The symptoms of a...

Gilomen Innovations big tire mudder secondary spring for the square puck type Team BOSS 30 mm secondary clutch that came factory on many polaris 900 and 1000 models.  This spring is designed to accomodate machines that have larger big tires...

Gilomen Innovations primary clutch spring for P90 standard clutch that comes on most models from 2013+ and the P90X clutch that come on the 2018+ Ranger 1000 models.  Choose your spring rate 

This is a factory Polaris P90 clutch cover plate with bushing fits 900-1000 Polaris UTV models.  New take off.   Clutch not included..

Clutch housing cover gasket.  If your rubber/foam gasket is shot its a good idea to replace it to insure the clutches and belt stay dry.   This gasket is made in the USA.   High density red material makes for superior sealing...

Gilomen Brand Helix for the boss square puck type 30 mm secondary clutch.  Choose your angle.  The boss clutch is the factory style clutch that was used on most 2016 and newer 1000 General, RZR, and 17-18 gen 1 Ranger 1000 models...

BlackMax adjustable primary weights for the Polaris standard p90 clutch found on most models from 2013+. These weights are made out of high carbon machine billet steel. The weights are adjustable using powerful rare earth magnets. If you are someone that...

Gilomen Innovations  Solid fixed clutch weight for the P90 primary clutch used on many models.  This weight is used in some of our clutch kits that we offer.   Replacement weights if one of your weights became damaged from a failed...

Polaris clutch housing screw part# 7519330 set of 8ea. 

These shims are for machines that are equipped with the OEM Boss secondary clutch. The shims are placed inside the secondary clutch using a screwdriver (installation process shown in photos). If your belt rides tight against the inner sheave of the...

These shims are for machines that have a Team Tied secondary clutch installed.  If you are still running the oem Team boss secondary clutch (square puck type clutch) then look into our boss secondary shim washers.   The shims are .030"...

WARNING! MAKE SURE TO MEASURE YOUR BUTTONS TO INSURE YOUR CLUTCH TAKES THESE 16.7 MM BUTTONS.  SOME MACHINES CAME WITH LARGER SIZED BUTTONS.   Dupont 16.7 mm (0.657" INCH) diameter clutch button set with rubber backing to absorb harsh...

Set of 60 big magnets and set of 24 small magnets.   These work with the Gilomen Innovations adjustable clutch weights.     

Set of 6 replacement bushings for Gilomen clutch weights.  Fits all bushed type Gilomen weights with 1/4" ID and flange.   Fits Blackmax, Torque Monster, and Mileage Master clutch weights.   These bushings are a multi layer metal...

High quality OEM Polaris roller pin.  The rollers ride on this pin on the spider.  3 required per spider.  SOLD EACH.       

High quality OEM Polaris roller washer.  Goes on next to the rollers on the spider.   SOLD EACH.    

Bolt holds clutch on the shaft.  Part number 7519306 subs to:  Part number 7519210  Used on many models.   Bolt Size  10X1.25X60 MM    

Genuine Polaris 7518412 clutch bolt with spacer 5132441 and washer 7556003.   Used in many models.   This is the main bolt that holds the primary clutch onto the crankshaft.         

High quality OEM Polaris roller with bushing inside for the spider used on most polaris P90 primary clutches.    Sold in each. 

Clutch Weight Pin Bolts and nuts (set of 3) 7512266

Blue composite washer for primary clutch.   Sold in each. 

Vespel special washer that goes on each end of the roller bearing on the primary clutch.   Sold in each. 

Spring spacer engagement shim.  This shim is designed to go under the spring in the primary clutch to raise the engaement rpm.  Most applications see an increase of 150-200 rpm by installing this shim.  You can install up to two shims in...

This is the jam nut that the factory used on all 2016 and newer drive clutches. The earlier 900 Ranger and RZR drive clutches did not come with this jam nut and are prone to having the spider unthread. If your clutch is missing the jam nut I highly...

Polaris OEM transmission input shaft seal.  This seal is pressed into the transmission housing behind the secondary clutch.   Polaris # 3235495